1. Dual time 24-hour hand
2. Hour hand
3. Button A
4. Minute hand
5. Crown
6. Crown - First click
7. Button B
8. Dual time minute hand
9. Second hand

Set the time: Move the crown to position 6 and turn.

**To set dual time (practical for a different time zone): ** Move the hour hand by pressing the A button for forwards and B for backwards.

Precise adjustment of the dual time: Pull the crown out to position 6 when the second hand is at the 12 o’clock position. Move the hand in 15-minute increments by pressing the A button for forwards and B for backwards.

Resetting the dual time hands position: Move the crown to position 6. Keep buttons A & B pressed at the same time for 2+ seconds, then release. Then press A & B again.

Additional information: The dual minute hand rotates one revolution at every quarter (15 minutes). This is a normal function of the movement.

• Movement: Seiko VD36 Quartz
• Water resistance: 3 ATM / 30 metres
• Features: More time zones
• Battery: SR920SW
• Glass: Sapphire crystal glass
• Case material: Stainless steel
• Strap material: Stainless steel
• Nickel free: Yes
• Max. wrist size: 20.8 cm
• Min. wrist size: 14.8 cm
• Strap width: 20 mm
• Case diameter: 42 mm
• Dial diameter: 37 mm
• Case thickness: 10 mm
• Crown height: 4 mm
• Lug width: 20 mm
• Lug to lug: 48 mm
• Weight: 134 g

Most watches have some level of water resistance. If your watch isn’t water resistant, it may be able to handle small splashes, but don’t risk it. If it has a leather band, don’t get it wet.

• Do not move the crown or push any buttons when your watch is in contact with water, as this may let water enter the case.
  
• If your watch is not water resistant, dip a cotton swab in a bowl of warm water with a drop or two of soap in. Squeeze the tip of the cotton swab to remove most of the water and gently rub the case.
  
• If your watch is water resistant, soak a soft cloth in a bowl of warm water with two drops of mild washing-up liquid added. Wring most of the water out of the cloth and gently rub the case with it.
  
  

If your metal watch has lost some of its lustre, you can bring it back by polishing it with a special microfibre cloth for cleaning jewellery.

1. Gently wipe down the band and case to remove any dirt, dust, or fingerprints.
2. For areas such as engravings, edges, and other details that are hard to reach, use a soft toothbrush.
3. Always dry your watch with a soft cloth or towel after cleaning to remove pollutants and prevent water spots or stains from forming.

• Store your watch in a dark, dry place to avoid corrosion and discolouration of the dial.
• Always replace the battery on a quartz watch as soon as it runs out. With time, an empty battery may start leaking, damaging the watch’s movement.
• Run mechanical watches at least two days a year to prevent gears and cogs from sticking.
• You should always get your watch serviced by a professional every 3 years.

Rule of thumb: Make sure your watch is the last thing you put on and the first thing you take off.

• Take your watch off and store it safely before engaging in any activity that could damage it.
• Take it off before engaging in any activity likely to make you sweat.
• Take it off before you shower, bathe, or go for a swim.
• Take it off before cooking or cleaning.
• Take it off before you go to bed.
• Don’t expose your watch to chemicals such as cologne, sunscreen, perfume, chlorine, hair gel, etc., as these can discolour, stain, or dull surfaces.
• Try to store your watch separately in a soft enclosure to prevent scratching and rubbing.
• If your watch has closures or clasps, close these to prevent tangling.
• Keep your watch stored in a dry, dark place, and avoid heat fluctuation.

The links with arrows are removable. The arrows show in which direction the pins should be pushed.

1. Use a pin pusher and remove the first pin. Set it aside.
2. Decide how many links you want to remove and then push out the corresponding pin.
3. Remove the undesired link(s). The more links you remove, the shorter the strap will be.
4. Connect the remaining links and insert the pin to connect them.*

*You may need a small hammer to help push the pin into place.

1. To make fine adjustments to the length using the clasp pins, push the pin in on one side and move the clasp slightly to lock it in place.

2. Repeat the process on the other side of the clasp.

3. Slide the clasp until the pins pop into the desired pinholes.

If you take care of your watch and keep it stored correctly, you should enjoy years of timekeeping precision. But even with the best care possible, you may find that your watch needs extra attention from time to time.

Take a look at common issues with watches here. If you can’t find what you’re looking for, our great Customer Service Team is only a phone call away.

To keep the warranty on your watch valid, don't expose it to water past the rated limit and make sure you keep the receipt.